Pic Programmers

Programming a single PIC16C84/F84 can be done via the card slot or dil socket. For those with twin chip 84's it is just as easy to program, you program the master chip in the M position first, then push the switch into the S position for slave.

(Always change to RB6 when using twinchip cards) For those with a pic84 and a 24c16 this can be done via the card slot or the dil socket The only difference is, program the 84 as a single 84 and the 24c16 in the M position.

All you need to add is a 15-18 volt AC/DC power supply and a printer cable to your computer.

Click here to download PIX113B, for uploading data onto pic via picpro & eproms via your phoenix/smartmouse.

Click here to download PixHelp, how to program via picpro & eproms via your phoenix/smartmouse.

Pic Programmer with Dil

£ 45.00

Pic Programmer with Zif

£ 45.00

Multi Pic Programmer

£ 45.00

PIC12C508/A PIC12C509/A PIC16F84 PIC16C84 are just a few of the chips the Multipicpro can program.

CardMaster Programmers

The Cardmaster can program most wafer cards.

Type	Cardmaster	Cardmaster2
PIC16F84(WHITE)
PIC16F84/24C16(GOLD)
PIC16F84/24C64 (BLUE)
PIC16F628(WHITE)
PIC16F876(WHITE)
PIC16F876/24C64(SILVER/DS9)
PIC16F876/24C128
PIC16F876/24C256
JUPITORCARD AT90S2343/24C64
FUNCARD AT90S8515/24C64
FUNCARD2 AT90S8515/24C128
FUNCARD3 AT90S8515/24C256

Click here for latest CardMaster software.

USB Infinity

£ 45.00

USB Infinity the lastest USB processor based programmer, programs your Gold, Silver Blue and Piccard2.

Card Master

£ 45.00

Cardmaster the lastest processor based programmer, if you download me some files I will program your Gold, Silver Blue and Piccard2 and I am upgradable to any new version that comes out via a plug in chip.

Standard Cardmaster just needs a 12volts unregulated power pack and a serial lead

Card Master 5

£ 45.00

Cardmaster5 is the lastest processor based programmer, if you download me some files I will program your Gold, Silver Blue, Fun ATMEGA and Piccard2 Very Quickly and i am upgradeable via a plug in firmware chip and i can program a fun card in less than 60 seconds.

Cardmaster2 just needs a 12volts unregulated power pack and a serial lead

PC Card Master

£ 45.00

I am one of the first programmers to fit in your PC, if you download me a Pic and an Eeprom file I do everything the Cardmaster does but fit in your floppy drive bay and am powered by an external powerpack which plugs into a socket at the back of the PC.

Standalone Programmers

Automate Professional Gold & Silver WaferCard Duplicator

£ 45.00

Card Copying without computer - No need to sit in front of PC for hours making multiple cards simply make one then use this device for the rest it will code protect the cards you make. Even take it out with you (2 x 9 volt battery required). Simply Insert card and press start (Reads the Data) Insert blank Card and press start (programmes the card) can be used on single C84,F84,F876 Gold/Silver Piccard2 wafer cards (Requires unprotected card to copy from)

• User Manual

Pic2Pic Copier - Stand Alone - NO PC Required

£ 45.00

This Unit uses Microchips Latest Algorithms.

Capable of copying the following unprotected Pics: 12C508, 12C508A, 12C509, 12C509A, 12CE518, 12CE519, 16C83, 16C84, 16F83, 16F83A, 16F84 & 16F84A

The 12C508A & 12C509A are programmed with the 11 times overprogramming algorithm as per Microchips latest programming specifications.

Reads & Writes V.Fast - 12C508A in 2 Seconds, 16F84A in 11 Seconds

It will NOT Copy Code Protected Chips, Deprotect or Write to Chips that are not BLANK! (Apart from 16C84 & F84 - Which it will erase before programming!)

1. Insert your unprotected MASTER PIC CHIP into the SOURCE PIC chip socket (Pin1 of Chip to Pin1 of Chip Socket – 8 or 18 Pin Chips)
2. 2. Set the type of Chip you want to copy by setting the jumpers on J1.
3. 3. Plug the Power Supply into Con1 of the Copier.
4. 4. Both the STATUS and the PROG O.K. LED's flash 4 times then extinguish – showing the Copier is ready for use (If this is not the case then there is something wrong with your copier).
5. 5. Insert a blank Pic Chip into the DESTINATION socket & press the GO button. (Pin1 to Pin1)
6. 6. The STATUS LED will light – Programming/Copy in progress.
7. 7. The PROG OK LED will light when Programming/Copy is complete.

Status Led & Flash Codes

• On - Programming in progress.
• 1 Flash - Verify Error (Problem in writing to DESTINATION Chip)
• 2 Flashes - Source Chip Code is Code Protected (unable to copy)
• 3 Flashes - Destination Chip is not BLANK!

Stand Alone Multi-Eeprom Copier / Duplicator

£ 45.00

Capable of copying the following I2C Eeproms.

24LC00, 24LC01, 24LC02, 24LC04, 24LC08, 24LC16, 24LC32, 24LC64, 24LC128, 24LC256. (Or Equivalent i.e. 24C16)

No Need to change the Firmware IC for different Eeproms, Select Eeprom type via 4 Way Header.

Seperate Read & Write Buttons, Option to Copy Slow Eeproms, 2 LED's indicate Status!

Functions Reads & Writes "Very Fast" - 24LC16 in 2 Seconds, 24LC64 in 3 Seconds.

Copies Eeproms from various Manufacturers - Microchip, SGS Thompsom (ST), National Semiconductor,Catalyst, Fairchild & Atmel. (Not XICOR - Gobble too much current! )

Has 3 Different Speed Modes. (To enable it to copy slower devices)

Normally Boots up in TURBO Mode.

Has the ability to read from the Eeprom in the ZIF socket (Destination) to the Eeprom in the Source Socket.

Unit can be disabled from READING the destination Eeprom - Stops accidental erasure of Source Eeprom.

The Source Eeprom can also be placed in the Lower half of the ZIF socket. (Destination Eeprom is located at the top of the ZIF socket)

Unit requires a 9 - 20V 100mA (AC or DC) power supply to operate.

Copier has 2 Headers to enable you to wire to an Eeprom in Circuit. (One Header for the Source Eeprom and one for the Destination Eeprom)

Copying Procedure.

1. Insert your MASTER Eeprom CHIP into the SOURCE Eeprom chip socket (Pin1 of Chip to Pin1 of Chip Socket)
2. Set the type of Size of Eeprom Chip you want to copy by setting the jumpers on J1.
3. Plug the Power Supply into Con1 of the Copier.
4. Both the STATUS and the PROG O.K. LED's flash the revision of Firmware, showing the Copier is ready for use.
5. Insert a Eeprom Chip into the DESTINATION socket & press the WRITE button. (Pin1 to Pin1)
6. The STATUS LED will light – Programming/Copy in progress.
7. The PROG OK LED will light and the The STATUS LED will extinguish when Programming/Copy is complete.

Status Led & Flash Codes

• On - Programming in progress.
• Flash - Verify Error - In writing to destination Eeprom
• 2 Flashes - Invalid Device Selected with Jumpers
• 3 Flashes - Communication Problem With Source Eeprom
• 4 Flashes - Communication Problem With Destination Eeprom

Multi-Eeprom Copier Programmer comes with a Dil socket to Zif socket